WA302
ULX1, UT1 바디팩 트랜스미터와 기타 또는 다른 악기에 연결하도록 제작된 악기용 케이블.
1/4 인치 플러그와 4핀 미니 커넥터(TA4F)로 되어 있으며 길이는 1.2 미터이다.
(악기용 시스템에는 제공된다.)
ULX1 바디팩 송신기
초경량에 뛰어난 내구성을 지닌 바디 팩 ULX1은 고성능에 부합하는 모든 특성을지니고 있다. 기타와 베이스뿐만 아니라 헤드원, 핀 그리고 악기용 마이크에 함께 사용된다. 활동의 자유성을 보장하기 위해서 벨트, 허리띠 또는 기타 스트랩에 클립으로 부착한다.
ULXS4 스탠다드 무선 리시버
Shure ULX? 스탠다드 무선 리시버는 활동성이 강한 뮤지션과 음향 설치업자에게 성능과 가격적인 면에서 특별한 가치를 제공한다.
다재다능한 ULXS4 리시버의 기능 설정은 부담이 없고 오디오 신호의 명료성을 제공한다.
SPEC
WA302
ULX1, UT1 바디팩 트랜스미터와 기타 또는 다른 악기에 연결하도록 제작된 악기용 케이블.
1/4 인치 플러그와 4핀 미니 커넥터(TA4F)로 되어 있으며 길이는 1.2 미터이다.
(악기용 시스템에는 제공된다.)
ULX1 무선 바디팩 송신기는 그룹/채널과 건전지 잔량을 나타내는 LCD창과 같은 한층 더 업그레이드 된 기술을 제공합니다. 주파수 및 전원 잠금 장치가 있어 9v의 건전지로 최대 8시간의 사용이 가능합니다.
본 바디팩 송신기는 ULXP4 또는 ULXS4 수신기 없이 사용이 불가능 합니다.
• 사용 주파수 대역
- 주파수 허가 필요 대역 : 554-590MHz[J1], 662-698MHz[M1]
- 주파수 허가 불필요 대역 : 925-932MHz[X3]
• 최대 동시 채널 수
- 주파수 허가 필요 대역 : 41채널
- 주파수 허가 불필요 대역 : 9채널
• 송신기 RF 출력
- 주파수 허가 필요 대역 : 30mW
- 주파수 허가 불필요 대역 : 10mW
• 3단계 건전지 잔량 표시
• 주파수 및 전원 잠금 가능
• 탈 부착 가능한 1/4파장 안테나
• TA4F 소형 4핀 인풋 커넥터
• 그룹/채널 LCD 디스플레이
• 오디오 게인 컨트롤 조절
• 입력 감쇄 스위치
• 과부하 시 피크 아이콘 표시
• 전원 on/off 스위치
• 8시간의 건전지 수명 (9V 건전지)
• 사용범위 : 100m (지역에 따라 다름)
스펙
ULX1 Transmitter Input
|
Microphone (pins 3 and 4 tied together) |
Guitar (with WA302) |
|
Connector |
TA4M |
TA4M |
|
Configuration |
Unbalanced, active |
Unbalanced, active |
|
Actual Impedance |
75 kilohms |
1 megohm |
|
Maximum Input Level |
-4 dBV (1.82 Vp-p) |
Gain Switch 0 dB: 5 dBV (5 Vp-p)
Gain Switch -20 dB: 25 dBV (50 Vp.p) |
|
Pin Assignments |
1 = Ground
2 = +5V through 4.5 kÙ (Microphone Bias)
3 = Audio
4 = FET active load |
1 = Ground
2 = No Connection
3 = Audio
4 = No Connection |
RF Carrier Frequency Range
470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
Effective Range
100 m (300 ft.) under optimal conditions
NOTE: Actual working range depends on RF signal absorption, reflection, and interference
Audio Frequency Response
25 to 15,000 Hz, +/- 2 dB
NOTE: Overall system frequency response depends on the microphone element.
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
1/4 inch connector (into 3000 ohm load): -2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
Modulation
+/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 microVolt for 12 dB SINAD (typical)
Image Rejection
80 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (reference +/- 38 kHz deviation)
>105 dB, A-weighted
System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
0.3% total harmonic distortion, typical
Power Requirements
ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
Ba ttery Life
8 to 9 hours (with 9V alkaline battery)
Operating Temperature Range
-20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
ULXS4 수신기
ULX® Standard UHF wireless (ULX-S)는 현역에서 활동하고 있는 아티스트나 전문 음향 설치 업자들에게 파격적인 성능과 가격을 제시합니다.
• 사용 주파수 대역
- 주파수 허가 필요 대역 : 554-590MHz[J1], 662-698MHz[M1]
- 주파수 허가 불필요 대역 : 925-932MHz[X3]
• 최대 동시 채널 수
- 주파수 허가 필요 대역 : [J1]:21채널, [M1]:20채널
- 주파수 허가 불필요 대역 : [X3]:9채널
• 송신기 RF 출력
- 주파수 허가 필요 대역 : 30mW
- 주파수 허가 불필요 대역 : 10mW
• 그룹/주파수 자동 스캔 설정
• 1440개의 선택 가능 주파수
• 5단계 오디오 미터
• RF 표시 LED
• 3단계 건전지 잔량 표시
• 다기능 그룹/채널 표시 LCD창
• 마이크/라인 스위치
• 탈착 가능한 1/4파장 안테나
• XLR 및 1/4”출력
• 견고한 플라스틱 섀시
• 1/2 랙 디자인
|
Compatible Systems Per Band |
Up to 20* |
|
Compatible Systems Using Multiple Bands |
62* |
|
Selectable Frequencies |
1440 |
|
Auto-Setup |
Scan / Channel Scan |
|
Detachable Antenna |
Yes |
RF Carrier Frequency Range
470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
Effective Range
100 m (300 ft.) under optimal conditions
NOTE: Actual working range depends on RF signal absorption, reflection, and interference
Audio Frequency Response
25 to 15,000 Hz, +/- 2 dB
NOTE: Overall system frequency response depends on the microphone element.
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
1/4 inch connector (into 3000 ohm load): -2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
Modulation
+/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 microVolt for 12 dB SINAD (typical)
Image Rejection
80 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (reference +/- 38 kHz deviation)
>105 dB, A-weighted
System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
0.3% total harmonic distortion, typical
Power Requirements
ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
Battery Life
8 to 9 hours (with 9V alkaline battery)
Operating Temperature Range
-20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
ULXP4, ULXS4 Receiver Audio Output
|
Connector |
Unbalanced (1/4 in.) |
Balanced (XLR) |
|
Actual Impedance |
3 kilohm |
Mic. Level: 1848 Ohms
Line Level: 75 Ohms |
|
Pin Assignments |
Tip = Hot
Ring/Sleeve = Ground |
1 = Ground
2 = Hot
3 = Cold |
|
Phantom Power Protection |
Yes |
Yes |
ULXP4, ULXS4 Receiver Antenna Input
|
Connector Type |
BNC |
|
Actual Impedance |
50 Ohms |
|
Nominal Input Level |
-95 to -30 dBm |
|
Maximum Input Level |
+6 dBm (-20 dBm recommended) |
|
Pin Assignments |
Shell = Ground, Center = Signal |
|
Voltage for Remote Power |
12 Vdc, 150 mA maximum |
RF Carrier Frequency Range
470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
Effective Range
100 m (300 ft.) under optimal conditions
NOTE: Actual working range depends on RF signal absorption, reflection, and interference
Audio Frequency Response
25 to 15,000 Hz, +/- 2 dB
NOTE: Overall system frequency response depends on the microphone element.
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
1/4 inch connector (into 3000 ohm load): -2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
Modulation
+/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 microVolt for 12 dB SINAD (typical)
Image Rejection
80 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (reference +/- 38 kHz deviation)
>105 dB, A-weighted
System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
0.3% total harmonic distortion, typical
Power Requirements
ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
Battery Life
8 to 9 hours (with 9V alkaline battery)
Operating Temperature Range
-20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
ULXP4, ULXS4 Receiver Audio Output
|
Connector |
Unbalanced (1/4 in.) |
Balanced (XLR) |
|
Actual Impedance |
3 kilohm |
Mic. Level: 1848 Ohms
Line Level: 75 Ohms |
|
Pin Assignments |
Tip = Hot
Ring/Sleeve = Ground |
1 = Ground
2 = Hot
3 = Cold |
|
Phantom Power Protection |
Yes |
Yes |
ULXP4, ULXS4 Receiver Antenna Input
|
Connector Type |
BNC |
|
Actual Impedance |
50 Ohms |
|
Nominal Input Level |
-95 to -30 dBm |
|
Maximum Input Level |
+6 dBm (-20 dBm recommended) |
|
Pin Assignments |
Shell = Ground, Center = Signal |
|
Voltage for Remote Power |
12 Vdc, 150 mA maximum |
RF Carrier Frequency Range
470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
Effective Range
100 m (300 ft.) under optimal conditions
NOTE: Actual working range depends on RF signal absorption, reflection, and interference
Audio Frequency Response
25 to 15,000 Hz, +/- 2 dB
NOTE: Overall system frequency response depends on the microphone element.
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
1/4 inch connector (into 3000 ohm load): -2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
Modulation
+/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 microVolt for 12 dB SINAD (typical)
Image Rejection
80 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (reference +/- 38 kHz deviation)
>105 dB, A-weighted
System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
0.3% total harmonic distortion, typical
Power Requirements
ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
Battery Life
8 to 9 hours (with 9V alkaline battery)
Operating Temperature Range
-20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
ULXP4, ULXS4 Receiver Audio Output
|
Connector |
Unbalanced (1/4 in.) |
Balanced (XLR) |
|
Actual Impedance |
3 kilohm |
Mic. Level: 1848 Ohms
Line Level: 75 Ohms |
|
Pin Assignments |
Tip = Hot
Ring/Sleeve = Ground |
1 = Ground
2 = Hot
3 = Cold |
|
Phantom Power Protection |
Yes |
Yes |
ULXP4, ULXS4 Receiver Antenna Input
|
Connector Type |
BNC |
|
Actual Impedance |
50 Ohms |
|
Nominal Input Level |
-95 to -30 dBm |
|
Maximum Input Level |
+6 dBm (-20 dBm recommended) |
|
Pin Assignments |
Shell = Ground, Center = Signal |
|
Voltage for Remote Power |
12 Vdc, 150 mA maximum |
RF Carrier Frequency Range
470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
Effective Range
100 m (300 ft.) under optimal conditions
NOTE: Actual working range depends on RF signal absorption, reflection, and interference
Audio Frequency Response
25 to 15,000 Hz, +/- 2 dB
NOTE: Overall system frequency response depends on the microphone element.
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
Transmitter Gain Adjustment Range
ULX1: 25 dB
ULX2: 25 dB
Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
1/4 inch connector (into 3000 ohm load): -2 dBV
Impedance
ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
Modulation
+/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
RF Power Output
ULX1, ULX2: 30 mW maximum
Dynamic Range
>100 dB, A-weighted
RF Sensitivity
1.26 microVolt for 12 dB SINAD (typical)
Image Rejection
80 dB typical
Spurious Rejection
75 dB typical
Ultimate Quieting (reference +/- 38 kHz deviation)
>105 dB, A-weighted
System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
0.3% total harmonic distortion, typical
Power Requirements
ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
Battery Life
8 to 9 hours (with 9V alkaline battery)
Operating Temperature Range
-20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
NOTE: Battery characteristics may limit this range.
Overall Dimensions
ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
Net Weight
ULX1: 79 g (2.8 oz.) without battery
ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
ULX2/SM86: 251 g (8.8 oz.) without battery
ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
ULXS4: 1049 g (2 lbs, 5 oz.)
ULXP4: 1105 g (2 lbs, 7 oz.)
ULXP4, ULXS4 Receiver Audio Output
|
Connector |
Unbalanced (1/4 in.) |
Balanced (XLR) |
|
Actual Impedance |
3 kilohm |
Mic. Level: 1848 Ohms
Line Level: 75 Ohms |
|
Pin Assignments |
Tip = Hot
Ring/Sleeve = Ground |
1 = Ground
2 = Hot
3 = Cold |
|
Phantom Power Protection |
Yes |
Yes |
ULXP4, ULXS4 Receiver Antenna Input
|
Connector Type |
BNC |
|
Actual Impedance |
50 Ohms |
|
Nominal Input Level |
-95 to -30 dBm |
|
Maximum Input Level |
+6 dBm (-20 dBm recommended) |
|
Pin Assignments |
Shell = Ground, Center = Signal |
|
Voltage for Remote Power |
12 Vdc, 150 mA maximum |
- WA302 기타/베이스 케이블
- ULX1 바디팩 송신기
- ULXS4 다이버시티 수신기
