|
16ch Analog/Dante Converter
ML-16D 16채널 아날로그/Dante 컨버터 ML-16D1U 크기의 16채널 아날로그 라인 인풋
/ 아웃풋 랙 마운트 Dante 컨버터
ML-16D는 16채널 아날로그 라인 입력 및 출력 신호를 Dante 신호로 변환할 수 있는 1U 크기의 소형 컨버터입니다. 이 제품은 Dante를 리던던시로 운용이 가능하며, D-sub 커넥터를 아날로그 라인 인풋/아웃풋으로 사용할 수 있게 설계되었습니다.
| | ML-32D | ML-16D | | Formats | | | Sampling frequency | 44.1k/48k/88.2k/96k Hz | | Quantization bit rate | 16bit/24bit | | ANALOG INPUTS/OUTPUTS | | | Line inputs | | | Connector | D-sub 25pin female | | Locking screws | No.4-40 UNC (inch type) | | Nominal input levels | +4dBu,
+6dBu (only when maximum input level is +15 dBu) | | Maximum input levels | +24dBu, +22dBu, +20dBu, +18dBu, +15dBu
(set by REF. LEVEL switches) | | Input impedance | 10kΩ or higher | | Line outputs | | | Connector | D-sub 25pin female | | Connector | No.4-40 UNC (inch type) | | Output impedance | 200Ω or lower | | Applicable load impedance | 2kΩ or higher | | Nominal output levels | +4dBu,
+6dBu (only when maximum outtput level is +15 dBu) | | Maximum output levels | +24dBu, +22dBu, +20dBu, +18dBu, +15dBu
(set by REF. LEVEL switches) | | PRIMARY/SECONDARY | | | Connector | RJ-45×2 | | Transmission protocol | Dante | | Gigabit Ethernet standard | 1000BASE-T(IEEE 802.3ab) | | Cables | Category 5e or faster STP cables | | Power | AC100V, 50/60Hz | | Power consumption | 22W | 14W | | Dimensions | 483(W)×45(H)×303.8(D)mm | | Weight | 3.5kg | 3.3kg | | Operating temperature range | 0～40˚C | | Standard accessories | Power cord, Rackmount screw kit, Owner’s Manual (including warranty) |
Audio performanceANALOG IN → Dante OUT| Frequency response | | | 20Hz/20kHz | +0.1dB/-0.5dB (-16 dBFS input, 44.1/48 kHz sampling frequency, JEITA) | | 20Hz/40kHz | +0.1dB/-0.5dB (-16 dBFS input, 88.2/96 kHz sampling frequency, JEITA) | | Distortion (THD+N) | 0.001% or lower (-1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA) | | S/N ratio | 113dB or higher (44.1/48/88.2/96 kHz sampling frequency, JEITA) | | Crosstalk | 115dB or higher (1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA) |
Dante OUT → ANALOG IN| Frequency response | | | 20Hz/20kHz | +0.1dB/-0.5dB (-16 dBFS input, 44.1/48 kHz sampling frequency, JEITA) | | 20Hz/40kHz | +0.1dB/-1.0dB (-16 dBFS input, 88.2/96 kHz sampling frequency, JEITA) | | Distortion (THD+N) | 0.001% or lower (-1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA) | | S/N ratio | 110dB or higher (44.1/48/88.2/96 kHz sampling frequency, JEITA) | | Crosstalk | 115dB or higher (1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA) |
|
|
